Lanner FW-8895 Bedienungsanleitung PDF herunterladen (Seite 17)

Motherboard Information

Chapter 3

Network Application Platforms

Jumper Settings

LCM_1: USB-type front LCD Message Display Module

(LCM). It supports both text and graphic type of LCM. The

board also facilitates Parallel -type LCM connector, refer to

jumper J23.

LCM_2: USB-type front LCD Message Display Module

(LCM). This connector is reserved for customization

purpose.

MGT1: RJ 45 management port connector

Note: Unlike the other management port

connector (MGT2), it doesn’t share an output port

(the Management port on the front panel) with

the IPMI signal Hence, no switch is required to

switch between these two signals.

MGT2: RJ 45 management port connector

Pin No. Function Pin No. Function

1 P5V_SB 2 P5V

3 USB_PCH_P5N 4

5 USB_PCH_P5P 6 HDD_LED_N

7 GND 8 GND

9 NTXD2 10 NRXD2

9 1

10 2

Pin No. Function Pin No. Function

1 MGT2_MDIP_0 2 MGT2_MDIN_0

3 MGT2_MDIP_1 4 MGT2_MDIN_1

5 MGT2_MDIP_2 6 MGT2_MDIN_2

7 MGT2_MDIP_3 8 MGT2_MDIN_3

9 MGT_LAN2_100# 10 MGT_LAN2_ACT#

11 MGT_LAN2_1G# 12 P3V3_AUX

Note: This MGT2 signal will not pass through

when the IPMI card is present (board reference NO.

OPMA1); The management port and IPMI share

the same output port (the Management port on

the front panel). Use the jumper OPEN2 to switch

between these two signals.

ATX5: 24-Pin ATX Power Connector

ATX1, ATX3: 8-Pin ATX Power Connector

SATA1: SATA Revision III Drive Connector

SATA2~SATA4: SATA Revision II Drive Connector

It is for connecting a 3.5’’ SATA harddisk to be served

as your system’s storage. The system can support up to

4 3.5" disks in maximum. The system’s BIOS supports

Pin No. Function Pin No. Function

1 +3.3V 2 +3.3V

3 +3.3V 4 -12V

5 Ground 6 Ground

7 +5V 8 PSON-

9 Ground 10 Ground

11 +5V 12 Ground

13 Ground 14 Ground

15 Power Good 16 NC

17 Stand-By 5V 18 +5V

19 +12V 20 +5V

21 +12V 22 +5V

23 3.3V 24 GND

Pin No. Function Pin No. Function

1 GND 2 12V

3 GND 4 12V

5 GND 6 12V

7 GND 8 12V

2 10

1 9

Pin No. Function Pin No. Function

1 P5V_SB 2 USB_PCH_P4N

3 USB_PCH_P4P 4 GND

5 PWR_LED- 6 FAULT_N

7 HDD_LED_N 8 PWRON_N

9 P3V3_AUX 10 PCH_PLTRST_LCM_N

Pin No. Function Pin No. Function

1 MGT2_MDIP_0 2 MGT_MDIN_0

3 MGT2_MDIP_1 4 MGT_MDIN_1

5 MGT2_MDIP_2 6 MGT_MDIN_2

7 MGT2_MDIP_3 8 MGT_MDIN_3

9 MGT_LAN_100# 10 MGT_LAN_ACT#

11 MGT_LAN_1G# 12 P3V3_AUX

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

Lanner FW-8895 Bedienungsanleitung Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computerhardware Lanner FW-8895